Numérique Moteur Pas À Pas Leadshine DM2282 Haute Performance 2-Phase avec 80-230 VAC Tension D'entrée et Max 8.2A Courant De Sortie

Category : Amélioration de l'habitat | Équipements électriques

USD 205.59USD 231.00

Numérique Moteur Pas À Pas Leadshine DM2282 Haute Performance 2-Phase avec 80-230 VAC Tension D'entrée et Max 8.2A Courant De Sortie

Description
Specification

Description

Notice:

We only supply genuine Leadshine servo motor drive with reasonable price, if your budget is limit, please contact our service man online and he she will recommend you the low price other supplier.

DM2282 2-Phase 32-Bit DSP Digital Stepper Drive

The DM2282 stepper drive adopts advanced features like electrical damping, anti-resonance, start-up smoothing, multi-stepping... With the input voltage of 90 - 230 VAC / 115 - 325 VDC and output current of 0.50 - 8.20 A, it is capable of driving a wide range of 2-phase stepper motors with high precision at extra smoothness, quietness, and very low motor heating.

Its multi-Stepping feature allows a low resolution step input to produce a much higher microstep output for smoother & quiet motor movement, and much lower motor heating. This feature will significantly improve the performance of your stepper control systems.

A DM2282 stepper drive is easy to setup and configure via DIP switches. There are 15 resolution settings from 400 - 25600, and 7 output current settings from 0.50 - 8.20. Also, a user can simply set the idle current to full (100%) or 50% of the output current via a DIP switch.

Features:

Step & direction or CW/CCW control

DSP-based stepper control technology

Anti resonance

Automatic motor identification and self configuration

Extra low noise

Extra smooth movement

Low drive & motor heating

Maximum frequency: 200KHz

Input voltage: 90 - 230 VAC / 115 - 325 VDC

Output current: 7 selections of 0.50 - 8.20A via DIP switches; or any value of 0.1-8.20A via software configuration

Micro steps: 15 selections of half - 128 step via DIP switches; or full - 512 step via software configuration

Automatic idle current reduction

Specification

Model: DM2282

Phase: 2

Control Mode: Step & Direction

Max Input Frequency: 200KHz

Input Voltage Range: 90 - 230 VAC /

115 - 325 VDC

Output Current: 0.50 - 8.20 A

Software Cofig. Resolution Range: 200 - 102,400 (increased by 200)

# of DIP Switch Resolution Configurations: 15

DIP Switch Resolution Setings: 400, 800, 1600, 3200, 6400, 12800, 25600, 1000, 2000, 4000, 5000, 8000, 10000, 20000, 25000

Software Cofig Current Range: 0.50 - 8.20A (increase by 0.1A)

# of DIP Switch Current Configurations: 7

DIP Switch Current Configurations: 2.2A, 3.2A, 4.2A, 5.3A, 6.2A, 7.2A, 8.2A

Logic Current Range: 7-16mA (10mA typical)

Logic Voltage Range: 4-5 VDC for pulse active high (default) , or 0-0.5V for pulse active low

Communication Type: RS232

Pulse enabled at: Rising edge

Idle Current Percentage: 50 %

Software Config. Idle Current Percentage: 0-100%

# of Digital Inputs: 3

# of Digital Onputs: 1

Step Width: 2,500 ns

Minimal Direction Setup Time: 5,000 ns

Protection: Over-current, over-voltage, under-voltage, phase-error, and over-temperature protection

Isolation Resistance: 500M Ohm

Environment: Avoid dust, oil fog and corrosive gases

Ambient Temporature: 0-50°C

Humidity: 40–95% RH

Operating Temporature: 0-70°C

Vibration: 5.9 m/s2 Max

Storage Temporature: -20-65°C

Specification: 7.87 X 5.39 X 3.19 Inches

Weight: 2.86 lbs

Electrical Specifications

Connector

Microstep Resolution Selection And Current Setting

Typical Connection

Mechanical Specification

Companion products

86HS35 (stepper motor)

HS3442 (Stepper Motor)

HS3468 (Stepper Motor)

HS3485 (Stepper Motor)

HS34100 (Stepper Motor)

HS4212 (Stepper Motor)

HS4215 (Stepper Motor)

HS4220 (Stepper Motor)

Real Photo:

Specification

Max Input Frequency : 200Khz

Numéro de Modèle : DM2282

Logic Current Range : 7-16mA (10mA typical)

Alimentation : AC

Control Mode : Step & Direction

Origine : CN (Origine)

Type de Moteur : Moteur pas à pas

Certification : NONE

Protection : Over-current, over-voltage, and stall

Step Width : 2,500 ns

Logic Voltage Range : 4-5 VDC for pulse active high (default)

Isolation Resistance : 500M Ohm

Input Voltage Range : 90 - 230 VAC / 115 - 325 VDC

Output Current : 0.50 - 8.20 A

Communication Type : RS232

Numérique Moteur Pas À Pas Leadshine DM2282 Haute Performance 2-Phase avec 80-230 VAC Tension D'entrée et Max 8.2A Courant De Sortie

Description

Specification

RELATED PRODUCTS